• home
  • posts
  • building your own sea kayak part 3 cockpit sealing fibreglassing
  • Posted July 11th, 2017
    0

    Building your own sea kayak part 3: cockpit, sealing & fibreglassing

    Building your own sea kayak part 3: cockpit, sealing & fibreglassing

    In the third instalment of the building your own sea kayak series, after a long break in the build over the winter the materials have arrived for the next stage of the process. The Petrel’s cockpit is recessed to give it a lower profile, which makes Eskimo rolls easier.  The forms are temporally glued to the boat and cockpit area is cut.

    Building your own sea kayak: construction of the cockpit

    Cockpit recess

    The recess is made of two pieces assembled using stitch and glue techniques. The recess back lowers the cockpit below the level of the deck. I made the recess out of 3mm marine ply wood.

    Building your own sea kayak: sections for the cockpit recess

    I then brushed on some epoxy resin and sanded to finish.

    Building your own sea kayak: epoxy resin added followed by sanding

    The finished recess…

    Building your own sea kayak: the finished recess

    The recess and the deck are then chiseled, planed and sanded to get a neat fit.

    Building your own sea kayak: a neat fit for the recess and the deck

    The recess is then glued into place ready for the next stage.

    Building your own sea kayak: the recess glued into place

    I will be sanding and filling this week and hopefully laying on the glass and epoxy over the next week or two.

    Sanding & fairing

    I began the fairing way back before Christmas but then the build went on hold for a good few months. I ordered the fiberglass and today finished the sanding. It was nice enough to move the boat outside in better light and get some decent photos of the whole boat.

    Building your own sea kayak: a view of the whole boat

    I’m pleased with the outcome of the sanding. It has opened up a few of the strips and requires a little filling with some ‘dookie schmutz’.

    Building your own sea kayak: another whole-boat view

    First I scraped the entire boat with a heavy duty paint scraper, then planed and finally sanded with a random orbital sander using 80,120,180 grit sand paper. I started with 40 grit on the hull as I manged to rip some of the strips with the plane.

    Building your own sea kayak: please do not touch!

    Building your own sea kayak: scraped and sanded

    The next stage will be to roll on a thin undercoat of epoxy resin before laying on the fiberglass. To do this I’m using 130g plain weave fiberglass. Then it’s flip the boat open and start on the inside, this way the separated deck and hull parts will be rigid enough to plane and sand.

    Seal coat

    A seal coat is a layer of epoxy applied to the boat before laying down the fiberglass to limit the absorption of epoxy when wetting out the glass later. It also adds an extra layer of protection and therefore more weight. Some people lay a seal coat, some don’t. As I am taking my time this layer will protect the wood while it sits about in a dusty cattle shed.

    I first take the hull off the forms to prevent any drips from the deck running down.

    Building your own sea kayak: hull removed to avoid drips

    I’m using West System’s 205/105 hardener/epoxy as recommended.

    Building your own sea kayak: hardener and epoxy resin

    The deck was a bit of a nightmare. I mixed up a small quantity of epoxy, poured it on and spread it about with a squeegee. The result was a thick gooey mess.

    Building your own sea kayak: a bit of a mess with epoxy resin on the deck

    Practice makes perfect I guess. For future reference don’t use so much epoxy.

    Building your own sea kayak: it turns out less is more when it comes to epoxy resin

    However from a distance it doesn’t look too bad.

    Building your own sea kayak: looking good from a distance

    Four sanding disks later and I’m still nowhere near getting a smooth clean finish.

    Building your own sea kayak: a whole lot of sanding and more still to do!

    I run out of disks and take the deck off the forms. I couldn’t resist taking this first opportunity to sit between the cockpit. Quite a special moment…my first glimpse of what my build might look like when paddling.

    Building your own sea kayak: Stuart takes a seat

    Hull back on the forms and a quick sand and brush off and it’s on with the epoxy. This time I used a roller and spread the layer very very thinly. It’s looks lovely and really brings out the colour of the wood.

    Building your own sea kayak: epoxy resin bringing out the beautiful colours in the wood

    Hopefully once the hull has set it won’t need much sanding – unlike the deck, which is going to take some time.

    Building your own sea kayak: hopefully no more sanding for this part?

    Building your own sea kayak: ready for fibreglassing!

    Next stage fibreglassing…cant wait!

    Fibreglassing the deck

    A busy work and home schedule has put my boat build on hold. I went up the farm to find it covered in a thick layer of dust. We were having a dry spell and it looked guaranteed to be dry for the next few days. So I took a gamble and loaded the boat up on the van to work on at home.

    Building your own sea kayak: taking a trip in (or should that be on?!) the van

    The last thing I did was add an undercoat of resin to the outside of the deck and hull. This turned out a bit of a mess up to say the least so I spent hours sanding it back to the wood.

    Back up the farm on a wet day to minimise the chance of dust – a last bit of fine sanding and a clean down and it was time to lay on the glass. The fibreglass comes in a woven fabric. This fabric is draped over the boat and cut to size. It is then lightly brushed to get out any folds and creases. A mix of epoxy and resin is then painted on with a roller, just enough to wet out the cloth.

    Building your own sea kayak: the woven fibreglass material is carefully placed

    Notice how the fibreglass weave is now clear once wetted out. It was left to dry for three hours. I then brushed on another layer of epoxy/resin as a fill coat to fill in the gaps in the weave.

    Building your own sea kayak: fibreglass wetted out and more epoxy added

    The finished result. Not bad for my first go, a good sand, varnish and polish should see it shining, but that will come later.

    Building your own sea kayak: fibreglassing finished and ready for more sanding

    The hull has been sanded back to the wood and is due to be glassed in the next couple of days, once I’ve fixed a split in one of the strips.

    Building your own sea kayak: a split fixed and sanding underway

    Building your own sea kayak: a sanded hull

    Once I have glassed the outside I have to plane, scrape and sand the inside before glassing also. Then I can build up the cockpit coaming, cut the hatches and install the skeg. Both halves will then be glassed together and bulkheads, footrests and seat installed ready to grace the water.

    On-board video of the Petrel in action.

     

    Part 2 is here.


    The views expressed in our blog are those of the author and not necessarily lowimpact.org's


    0 Comments

    Leave a comment

    We welcome questions.

    There’s a crash coming – a slap from Mother Nature. This isn’t pessimistic; it’s realistic.

    The human impact on nature and on each other is accelerating and needs systemic change to reverse.

    We’re not advocating poverty, or a hair-shirt existence. We advocate changes that will mean better lives for almost everyone.

    Sign up to our newsletter

    Facebook icon Twitter icon Youtube icon

    All rights reserved © lowimpact 2023